2/16/2024 0 Comments Automatic pool cover shear pin![]() ![]() SAVE-T COVER II® MEETS ASTM F 1346-91 CLASS PCS WHEN USED AS INSTRUCTED. FAILURE TO FOLLOW ALL INSTRUCTIONS MAY RESULT IN INJURY OR DROWNING.DO NOT WALK ON COVER EXCEPT IN AN EMERGENCY.NON-SECURED OR IMPROPERLY SECURED COVERS ARE A HAZARD.REMOVE COVER(S) COMPLETELY BEFORE ENTRY OF BATHERS, ENTRAPMENT POSSIBLE. ![]() REMOVE STANDING WATER - CHILD CAN DROWN ON TOP OF COVER.Inspection Procedure for Wear and Deterioration. Please take the time with your SAVE-T COVER II ® representative to go over this list to be sure that you understand the importance of the proper use of your pool cover. Did you receive drowning prevention information? Did a representative offer you assistance on how to maintain a safer pool area?ĥ. Were you notified of the importance of latching your cover every time the cover is closed?Ĥ. Were you notified of the importance of removing all standing water off your cover for safety and operation?ģ. Placing the cover pump in position when the cover is closed.Ģ. Chemical application as it affects the coverį. Has a representative from the company who installed your SAVE-T COVER II ® cover explained to you the proper operation of the system?ī. Turn off electrical breaker when the cover will not be used for extended periods of time or as an added layerofprotectionagainstunauthorizedoperation.Alwaysturnoffbreakerbeforeservicingthecover.įoryourbenefit,pleasedoublecheckthefollowingitemswithyourinstaller/representativetoaidinyourunderstanding of the use of your cover.ġ. Remove and safely store the key when the cover is not in use.ģ. ![]() To reduce the risk of injury, do not permit children to operate this product.Ģ. If you use the procedure above and cannot get the cover adjustment to change, call your local service company for assistance.WARNING:When installing and using this electrical equipment, basic safety precautions should always be followed, including the following.ġ. NOTE: Some covers systems are supplied with this adjustment feature disabled. ![]() However, a little brake must be left on both sides at all times to prevent the rope from becoming tangled because of backlash. When possible, take the brake off the side coming back slowest by loosening the wing nut on that side. Make sure the cover is stopped and the key or power is in the “off” position.Īdjust the cover by tightening the wing nut (clockwise) on the side that consistently comes back first.Īdd only a little brake at a time to avoid applying too much tension. You should always determine which adjustment to make by observing the evenness of the cover as it is coming off the pool.Īdjusting the cover is accomplished by tightening or loosening the wing nut on the brake mechanism (see illustration). Our exclusive brake adjustment makes it quite simple for you to do the adjusting yourself, avoiding a service call. However, it is possible for extreme changes in the cover condition to cause the cover to begin to run unevenly. "COVER RETRACTS UNEVENLY: Once your cover is installed it is unlikely that it will require any adjustment. To get the brakes back in place, loosen the two outer bolts and rotate the square shaft until the brakes are in place. I've found the manual for the SAF T 2 cover, but it doesn't specify the names of the parts that I can tell. The problem is, I want to call and get some quotes, but I don't know the names of all these parts to ask. We want to get the guides to stay back on the metal disks, get the rope all organized, and on the opposite side of the motor (see pic) get that area straightened out (suggested to do by previous owner). We are do it ourselves type of people, and would love to fix the ropes and guide to the metal wheels, but thinking I'm going to call out a pro for this since it's so old and we don't know what we are doing (yay us! ). Now our rope is not pulling back nicely and you can see our rope is all disorganized and that needs fixed too. What I would like to know, what is the name of that part that I have circled? The part that we cannot get to stay on the round metal disks, no matter what adjustment, it ends up coming off once we get going on opening or closing the cover. I think it sprayed up to parts that we should never have greased and now we have a problem. When we were trying to find out why our pool cover wasn't working (and motor just spinning, spinning, spinning), we added some WD-40 to parts in the motor. Recently our shear pin broke and we eventually figured out what it was and how to replace it (done, but leading up to figuring it out and replacing it, we did some other things that I think may have caused a new problem). That's really the least of the problems as of this point. Right now, one side of pool cover opens a few inches earlier than the other. Per previous owner, the rails installed have never been right and it causes problems with the cover. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |